|
General Information
|
| Manufacturer |
Bose
|
| Manufacturer Part
Number |
P2600A
|
| Product Name |
PowerSpace Power
Amplifier |
|
Overview
|
|
Ideal for zone-expansion
applications, Bose PowerSpace amplifiers enhance any premium
commercial sound installation with clean, reliable power (and
digital connectivity). A Bose AmpLink input allows for
multiple channels of uncompressed, low-latency digital audio
from Bose DSPs via a single Cat 5 cable. The PowerSpace P2600A
provides 600 watts per channel and features versatile outputs
that give you the flexibility to deliver full channel power to
either low or high-impedance loads (without bridging)
and even send double power to a single zone. For premium
commercial applications, Bose PowerSpace amplifiers provide
the power and performance to get the job done. pure and
simple.
|
|
Features
|
- 600 watts per channel and compatible with
Bose loudspeakers, DSPs, and controls to create complete
commercial sound system
- Bose AmpLink input for simplified
multichannel digital audio connection to compatible DSPs,
reducing terminations and related points of failure
- Load-independent outputs deliver full channel
power to either low-impedance (4-8 Ω) or high-impedance
(70/100V) loads without bridging
- I-Share output delivers 2x power level into
low-impedance (2-4 Ω) or high-impedance (70/100V) loads by
combining the current of both channels
- Auto-standby mode saves power when audio
signal falls below a set threshold after 20 minutes, then
wakes when audio returns
|
|
Specifications
|
| Amplifier
Power |
2x 600 W (THD+N less than 0.04%,
1 kHz, 4-8 ohm, 70/100V) |
| I-Share Mode Power |
1x
1200 W (2-4 Ohm, 70/100V) |
| Gain
(Low-Z mode) |
35dB |
| Gain
(70V mode) |
35dB |
| Gain (100V mode) |
35dB |
| Frequency Response |
4-8
Ohms: 20 Hz – 20 kHz (more or less than 1 dB at 1 W); 70/100V:
Same as 4-8 Ohms with 50 Hz high-pass filter |
| Channel Separation (Crosstalk) |
More
than 80 dB at 1 kHz, More than 65 dB at 20 kHz |
| Dynamic Range |
more
or less than 100 dBA (at rated power) |
| Audio
Latency |
Less
than 1 ms (any analog or AmpLink input to loudspeaker output) |
| Input
Channels |
2
balanced (Analog), 8 digital (AmpLink)
|
| Connectors |
6-pin
Euroblock (Analog), RJ-45 (Input) AmpLink
|
| Input
Impedance |
10 k
ohms
|
| Maximum
Input Level |
22
dBu (at 14 dBu sensitivity setting) |
| Sensitivity |
-10
dBV / 4dBu / 14 dBu |
Audio
Outputs
|
2
(Speaker), 8 Digital (AmpLink)
|
Audio
Connectors
|
4-terminal block (speaker), RJ-45
(Thru) AmpLink
|
| Power LED |
Solid
white: Power is on. Blinking white: Unit is in auto standby
mode. Solid red: Power supply fault, Blinking Red: Thermal
fault.
|
| Input
Signal LED |
Green:
Signal present. Amber: Input is near clipping. Red: Input is
clipping
|
| Output
Limit LED |
Amber:
Amplifier limiting an output. Blinking red: Amplifier muted.
Solid red: Amplifier or thermal fault |
| Controls,
Front Panel |
Power
On/Off |
| Controls,
Rear Panel |
Amplifier
mode DIP switches, input sensitivity switch, input select dial,
mute, output attenuators |
| Mains
Voltage |
100
VAC – 240 VAC (More or less than 10%, 50/60 Hz) |
| AC
Power Consumption |
120
VAC: 25 W (Auto standby), 570 W (Max); 230 VAC: 25 W (Auto
standby), 570 W (Max)
|
| Mains
Connector |
Standard
IEC (C14) |
| Protections |
V
peak/V rms limiters, high temperature, output short, extra high
frequency (EHF), excessively low or high AC line
voltage
|
| Operational
Temperature Range |
0 C
to 40 C |
| Dimensions
(H x W x D) |
1.7"
x 19" x 16.5" |
| Weight |
13.7
lb |
