General Information

Marketing Information

DYNACORD´s COBRA-4-TOP is an active 3-Way cabinet for use as a nearfield cabinet in compact line arrays and other demanding applications, where wide horizontal coverage, extremely low distortion and a low sensitivity against acoustic feedback are mandatory. Depending on the application, the COBRA-4-TOP cabinet can be used up to 40m throw distance.
The mid-range of the COBRA-4-TOP uses selected DYNACORD C8 cone transducers in a line array configuration. The C8 transducers show significantly lower distortion than typical horn/compression driver combinations. Therefore an extremely natural sound quality over large distances can be achieved.
For the high frequencies of the COBRA-4-TOP an Electro-Voice DH2T titanium diaphragm driver and a HPT94 constant directivity horn are used in order to prevent any set-up and adjustment problems for the main direction and the near field.
The DYNACORD COBRA-4-TOP uses a dual vented direct- radiator design equipped with an Electro-Voice EVX155 for the low frequencies. For Near-Fill and Side-Fill applications and for the reinforcement of speech the COBRA-4-TOP cabinets can be used fullrange without any problems.
The cabinet is equipped with an electronic circuit called VOICE COIL TRACKING PROTECTION. This circuit senses the terminal voltage of the transducers and simulates the thermal behaviour of the transducer voice coils. In case of potential thermal overload the power applied to the speakers is reduced to a safe level. Power amps up to 1200W/8Ohms can be used in order to have maximum dynamic range without the danger of thermal overload in non-controlled situations. The VOICE COIL TRACKING PROTECTION exhibits “soft” switching characteristics, so no annoying clicks or pops are audible. The circuitry automatically resets after the voice coil temperatures have reached a safe value.
The COBRA-4-TOP cabinet is made of 18mm birch plywood. All corner joints and braces are grooved and glued. The cabinet´s surface is coated with an extremely durable Polyurethane which exceeds the quality of a standard lacquer finish by an order of magnitude. A powder coated steel grille and a lockable cover protects the COBRA-4-TOP against damage during transport and bad environmental conditions.
The connector panel uses two 8-pole Speakon connectors (IN/OUT) for a safe connection and easy daisy-chaining to other cabinets.When using DYNACORD power amp racks the whole system can be wired with 8-pole Speakon cables without any danger of accidental wiring mistakes. Four recessed rigging tracks and two webbing-strap points can be used for easy “flying” of the COBRA-4-TOP cabinets. The cabinet is equipped with four large ABS feet that allow easy stacking and a “snap-on flying” even in angled positions. Two handles and four heavy-duty castors on the rear side guarantee easy and safe transport.

• Cabinet: MID - HIGH Cabinet
• Configuration: Compact line array / active 3-way
• Nominal impedance (LOW - MID - HIGH): 8 Ohms - 8 Ohms - 8 Ohms
• Rated power RMS (LOW - MID - HIGH): 400 W - 200 W - 100 W
• Program power (LOW - MID - HIGH): 800 W - 400 W - 200 W
• SPL 2,83 V / 1m 1 W / 8 Ohm: 100 dB
• Max. SPL 1m (calculated): 131 dB
• Frequency response ( -10dB ): 90Hz - 17kHz
• Coverage angle 1 kHz (-6dB): H 120° x V 30°
• Coverage angle 10kHz (-6dB): H 90° x V 40°
• Active crossover frequency: 124Hz - 700Hz - 4kHz
• Voice coil tracking protection: LOW - MID - HIGH
• Connector wiring HIGH: 8-pole 4+/4-
• Connector wiring MID: 8-pole 3+/3-
• Connector wiring LOW: 8-pole 2+/2-
• Dimensions (W x H x D): 600 x 495 x 717 mm
• Enclosure material: Birch plywood 18mm
• Finish: Black polyurethane
• Grille: Powder coated steel
• Handles: 2
• Ancra Tracks: 4
• Webbing strap point: 2
• Front cover: 1
• Castors: 4