Electro Voice P2000 Power Amplifier 2x900 Watts @4Ohms THX Approved 3U

Precision Series™ Power Amplifiers P2000

1,200 watts per channel at 2 ohms
Neutrik Speakon® output connectors allow use of heavy-gauge speaker wire for low-loss connections
Extremely low dynamic distortion ensures excellent sound quality
Three rack spaces

• 560 watts per channel at 8 ohms, 900 watts per channel at 4 ohms, 1,200 watts per channel at 2 ohms

• Neutrik Speakon® output connectors allow use of heavy-gauge speaker wire for low-loss connections

• Extremely low (<0.01%) dynamic distortion ensures excellent sound quality

DESCRIPTION

The Electro-Voice P2000 Precision SeriesTM amplifier is a very-high-quality power amplifier designed to elicit maximum performance from any speaker system. Its ultralow distortion and powerful amplifiers ensure that program material will be amplified very accurately. Each channel of the P2000 delivers more than 500 watts continuous average power into 8 ohms, 800 watts into 4 ohms and 1,000 watts into 2 ohms over the full audio frequency range. In the bridge mode, the amplifier can deliver more than 1,600 watts into 8 ohms and 2,000 watts into 4 ohms at less than 1% THD. The power supply, with its large toroidal transformer,
gives the amplifier impressive headroom and current output.

The P2000 contains 32 high-power output devices with 8,000 watts of dissipation capability. These devices are protected from overheating by four, three-speed, temperature-sensitive fans. The fans are quiet enough to permit use of the P2000 in noise-sensitive applications such as recording studios and houses of worship.
The output devices are mounted to a massive, extruded-aluminum heat sink that is engineered to minimize thermal gradients and allow the amplifier to operate safely into low-impedance loads. The output devices have a maximum junction temperature of 200 °C (392 °F), so high operational temperatures present no problems. The output devices are mounted directly to the heat sink without mica insulators to ensure better dissipation of heat. Many electronic circuit innovations exist in the P2000. Among the most novel of these circuits is the Mirrored Frontend Power Supply BridgeTM. This design ensures complete symmetry for each bridged amplifier and both signal polarities, and eliminates asymmetrical rise and fall times. The Dual Differential Discrete TopologyTM is part of the front end of the amplifier and uses discrete electrical components instead of integrated circuits to help the P2000 achieve its phenomenally low distortion. The P2000 has sophisticated protection circuits that guard it and the load from problems. Protection circuits guard against overload, overtemperature, shorted outputs, radio-frequency interference and dc faults. The output devices are protected against damage from reverse feeding of electrical energy (back EMF) and are switched on via relays to avoid transients which could damage speakers.

The P2000 has built-in limiters to protect speakers from the deleterious effects of amplifier clipping. The limiter’s action is governed by very sophisticated input/output comparators which have acoustically optimized time constants to preserve the integrity of the source. The limiter’s time constants are switchable fast/
slow, so the limiter may be matched to the application for which the amplifier is being used.

The P2000 has built-in switchable high- and low-cut filters. These filters attenuate infrasonic and ultrahigh-frequency signals, preventing them from being amplified; this allows more effective use of the amplifier’s power and adds a measure of load protection. These filters are switchable on/off for use in applications utilizing
frontend units (like crossovers or equalizers) which have these filters built-in. A multifunction display keeps the user informed of the operating status of the amplifier. Separate LED displays for each channel show power on, input signal, output signal, limiter on and protection active.

The P2000 has electronically balanced XLRtype input and output connectors that allow easy, problem-free connections and signal routing. The P2000 has an input routing switch that allows selection of either normal dualchannel operation, or parallel mono operation, which routes an input to both channels but still allows for independent level control. The P2000 also has a constant-gain option which allows the voltage gain to be fixed. This permits different amplifiers to be used in fixed installations without rebalancing, and ensures headroom is not wasted.

The P2000’s professional Neutrik Speakon® output connectors provide a sturdy, reliable connection and allow use of heavy wire for lossfree signal transmission. There are separate output connectors for channels A and B, and for the bridge mode. The bridge-mode connector is sealed with a plastic cover to prevent connection errors.

To prevent ground loops from occurring, the P2000 is equipped with a ground-lift switch. When the amplifier is operated in a rack with units of different ground potential, the switch may be adjusted to eliminate hum. Calibrated, detented potentiometers on the front panel regulate the gain of the P2000. The panel nomenclature shows the amount of attenuation accurately. The P2000 also has a constant-gain option which, with input level controls full clockwise, provides a 26-dB voltage gain that is identical to that of all Electro-Voice Precision SeriesTM amplifiers in the constant-gain option, regardless of power rating. This makes it possible to exchange amplifiers of different power ratings without upsetting delivered sound pressure levels or spectral balances.

The Electro-Voice P2000 is the choice for serious, professional amplification applications which require optimum sound quality, speaker protection, and the ighest level of construction quality and long-term reliability.

Specifications

• Conditions:
  1. 0 dBu = 0.775 V rms.
  2. Dual-mode ratings are for each channel, both operating, unless noted.
  3. 120-volt ac line voltage maintained throughout testing.
  Continuous Rated Output Power (20- 20,000 Hz at less than 0.1% THD, both channels driven per EIA RS-490), Dual Mode, 2 Ohms: 1,000 watts
  Bridged Mode, 4 Ohms: 2,000 watts
  Dual Mode, 4 Ohms: 800 watts
  Bridged Mode, 8 Ohms: 1,600 watts
  Dual Mode, 8 Ohms: 500 watts
  Continuous Rated Output Power (1 kHz, 1% THD, both channels driven per EIA RS-490),
  Dual Mode, 2 Ohms: 1,200 watts Bridged Mode, 4 Ohms: 2,400 watts Dual Mode, 4 Ohms: 900 watts
  Bridged Mode, 8 Ohms: 1,800 watts Dual Mode, 8 Ohms: 560 watts
  Power Bandwidth (+0, –1 dB, reference 1 kHz), Any Mode, 4 Ohms: 10-30,000 Hz
  Frequency Response
  (+0, –3 dB, reference 1 kHz/1 watt):<10-30,000 Hz

• Voltage Gain, 1 kHz, Any Mode, Constant- Gain Option:1 26 dB
  Input Sensitivity, 1 kHz, Dual Mode for 800 Watts into 4 Ohms: 0 dBu (775 mV)
  Maximum Input Level (reference 1 kHz): +20 dBu (7.75 V)
  Input Impedance (per channel, 20-20,000 Hz), Balanced: 20 kilohms
  Phase Response (at rated power, any mode, 10-30,000 Hz): ± 22.5 degrees
  THD Plus Noise at 1 kHz (at rated power, measurement bandwidth 80 kHz): <0.01%
  IMD (SMPTE) (60 Hz/7 kHz,): <0.01% DIM 30 (composite square-sine wave
  band-limited to 30,000 Hz): <0.01% DIM 100 (composite square-sine wave
  band-limited to 100,000 Hz): <0.01%
  Rise Time (10% to 90% at rated power, any mode):
  <2.5 microseconds Slew Rate, Any Mode: >35 V/microsecond
  Damping Factor, Any Mode: >300
  Amplifier Protection: Excessive output voltage; shorted loads; excessive phase shift; rf interference; overtemperature; excessive back EMF; In-rush current limiter

• Load Protection:
  Start-up/shutdown transients; dc fault; infrasonic signals; low ac line voltage; nonlinear signal limiter
  Output Topology:
  True complementary symmetry with ungrounded collectors (no mica insulators means better heat transfer)
  Output Devices,
  Total Number: 32 devices Pd(max) Rating: 250 watts Ic (collector current): 20 amps dc Tj(max): 200 °C (392 °F) Controls and Switches,
  Rear:
  Hi-Lo-Cut Filter(On/Off); Bridged Mode switch (Bridged/Normal); Limiter mode (Fast/Slow); Circuit ^ To Chassis Switch (Grounded/Ungrounded); Input Routing (Parallel Mono or Dual Stereo)
  Front:
  Two calibrated input level controls; power switch
  Front-Panel Indicators: Five LED’s per channel (10 total) for power on, input signal, output signal, limiter on and protect on Connections,
  Input:
  3-pin female XLR-type connectors for each channel in parallel with a 3-pin male XLR-type output connector for easy signal routing; the XLR connectors are wired according to the IEC 268 standard: pin 1 shield, pin 2 positive, pin 3 negative
  Output: Neutrik Speakon® NL4MP for channels A, B and for bridged mode
  Power: 12-gauge, 3-wire, permanently attached power cable; no ac plug supplied

• Operating Voltage:
  120 V, 60 Hz ac
  Power Consumption (both channels operating in dual mode, 1/8 power),
  4 Ohms: 800 VA

• Dimensions,
  Height: 132.5 mm (5.25 in.)
  Width: 483 mm (19.0 in.)
  Depth: 426 mm (16.8 in.)
  Color: Gray

A-20050314-1250-117-L

*This item is BRAND NEW - not refurbished. It comes with all manufacturer supplied accessories, and full manufacturer's USA warranty.