General
Information |
Manufacturer
|
Listen Technologies |
Manufacturer Part
Number |
CLD1-CX
|
Product Name
|
Compact Loop Driver, No Mic
|
Overview |
The CLD1
Compact Loop Driver is designed for counter systems and
small area perimeter loop systems. Measuring only 5" x
2.9" x 1.4" and with an output current of 2.4 A (RMS), the
CLD1 is the smallest and highest performance amplifier in
its class. The CLD1 offers certainty of performance and
the lowest lifetime cost available.
Audio quality is ensured with metal loss correction (MLC)
combined with usual high standards of design. The CLD1 is
designed for flexibility and convenience, featuring two
separate microphone inputs with independent level
controls, one of which can be configured as a line input.
All cable connections are made on a single face of the
unit, adding flexibility and further simplifying
installation |
Features |
Kit includes a
pre-formed loop for counter type installations
Low lifetime cost
Very compact
Two independent inputs
featuring one microphone input and one switchable
microphone/line input
Metal loss compensation
All connections to a
single face for installation convenience
The CLD1-CX Compact Loop
Driver is specified
The audio hearing loop
driver shall, in accordance with IEC60118-4,
continuously deliver 2.4 A (RMS) when excited with a
continuous 1 kHz sine wave
It shall cover an area
of at least 377 sqft with a room aspect ratio 3:1
according to IEC 60118-4:2006 standard
The driver shall have a
frequency response of at least 80 Hz to 6.5 kHz +/- 3
dB with THD+N less than 0.2 percent
The unit shall
incorporate audio processing to maximize the
intelligibility for individuals with a t-coil hearing
aid
The unit shall
incorporate metal loss correction to rectify frequency
caused adjacent metal structures
|
Specification |
Includes
|
One CLD1 Compact Loop Driver
One GE00001 Multi-Turn Preformed Loop for CDL1
One Handbook and Installation Instructions
One 12 VDC Power Supply (North America) |
Audio
|
Frequency Response
|
80 Hz to 6.5 kHz +/- 3 dB
|
Maximum Output Level
|
Correct system frequency response
due to metal structures
|
Distortion
|
THD+N less than 0.2 percent, 1 kHz
Sine Wave at Full Current
|
AGC
|
Optimized for Speech, Dynamic
Range more than 36 dB
|
Micophone Input
|
Unbalanced 3.5 mm Mono Connector
for Electret Microphone, 6 VDC Bias
|
Line Input
|
Switchable Line/Microphone,
Unbalaced 3.5 mm Mono Connector
|
Controls
|
Gain Control
|
Front recessed input level control
|
Cooling
|
Natural Convection
|
Indicators
|
Drive Current Indication
|
Front Panel LED Indicates Current
Peaks
|
Interconnections
|
Loop Connector/s
|
Level Cable Clamp
|
Loop
|
Perimeter Loop-Coverage
|
1:1 Aspect Ratio: 215 sq ft
2:1 Aspect Ratio: 323 sq ft
3:1 Aspect Ratio: 377 sq ft
Condition 1: Loop must be 3-6 ft. (1-2 m) above or
below the receiver height
Condition 2: There should be no metal structures in
the plane of the loop
Condition 3: There must be sufficient voltage to
drive the loop |
Power
|
VOX Switching
|
To control prioritization of
microphone 1 input
|
Compliance
|
UL Listed
|
Power
|
12 VDC
1.0 A
18 W
45 - 65 Hz
Power Switch/LED on Front Panel
|
Drive Voltage
|
3.2 V (RMS)
4.5 V Peak at Maximum Output Current
|
Drive Current
|
2.4 A (RMS)
3.4 A Peak with 1 kHz Sine Wave
|
Drive Current Peaks
|
Short Term More than 4.8 A
|
Physical
|
Mounting
|
Freestanding, Wall Mounting
|
Cable Length
|
10 AWG: Max distance at
full current, 268 ft
14 AWG: Max distance at full current, 247 ft
18 AWG: Max distance at full current, 168 ft
22 AWG: Max distance at full current, 94 ft
FB1.8: Max distance at full current, 328 ft
|
Environmental
|
Relative Humidity
|
IP20 Protection, 20 to 90 percent
Relative Humidity, 32 to 95 degrees percent
|
Weight and Dimensions
|
Dimensions
|
5.0" x 1.4" x 2.9" |
Weight
|
2.2 lbs
|